Opel Astra A

1991-1998 of release

Repair and operation of the car



Opel Astra A
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Ventilation and heating
- 5. Power supply system
   + 5.1. Carburetor engines
   - 5.2. Models with fuel injection
      5.2.1. Technical characteristics
      5.2.2. Precautionary measures
      5.2.3. Elements of system of injection of fuel
      5.2.4. Unleaded gasoline
      5.2.5. Electronic control unit
      5.2.6. Casing of the air filter
      5.2.7. Air filter
      5.2.8. Resonator, air filter
      5.2.9. Fuel injection block (Multec of TsVT)
      5.2.10. Case of a butterfly valve (Multec of MW)
      5.2.11. Case of a butterfly valve (Multec-S)
      5.2.12. Case of a butterfly valve (Motronic M 1.5)
      5.2.13. Case of a butterfly valve (Motronic M 2.5 and M 2.8)
      5.2.14. Case of a butterfly valve (Simtec)
      5.2.15. Fuel injector of Multec of TsVT
      5.2.16. Fuel injectors of Multec of MW
      5.2.17. Fuel injectors (Motronic M 1.5)
      5.2.18. Fuel injectors (Motronic M 2.5 and M 2.8)
      5.2.19. Fuel injectors (Simtec)
      5.2.20. Fuel pressure regulator
      5.2.21. Sensor of provision of a butterfly valve
      5.2.22. Potentiometer of a butterfly valve
      5.2.23. Solenoid of system of idling
      5.2.24. Electromagnetic valve of system of idling
      5.2.25. The solenoid regulating air supply in system of idling
      5.2.26. Pressure sensor in an inlet collector
      5.2.27. Sensor of speed of rotation and provision of a bent shaft
      5.2.28. Sensor of temperature of cooling liquid
      5.2.29. Oxygen sensor
      5.2.30. The sensor of temperature of the arriving air
      5.2.31. Air stream sensor
      5.2.32. Sensor of detonation combustion of fuel
      5.2.33. Sensor of position of the camshaft
      5.2.34. Blowing-off valve of the coal filter
      5.2.35. Fuel pump
      5.2.36. Fuel filter
      5.2.37. Accelerator rope
+ 6. System of decrease in toxicity
+ 7. Coupling
+ 8. Transmissions
+ 9. Half shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
+ 13. Electric equipment
+ 14. Electrical circuitries


0a910c3c




5.2.24. Electromagnetic valve of system of idling

MOTRONIC M 1.5

Removal and installation

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Release a fixing clip and disconnect the socket of connection of the electromagnetic valve.
3. Turn off fixing screws, disconnect hoses and remove the valve.
4. Installation is carried out upside-down removals.

MOTRONIC M 2.5 and M 2.8

Removal and installation

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Disconnect a hose under the air filter from the case of a butterfly valve.
3. Lift a forward part of the car and remove protective guards of the engine.
4. From below the car disconnect the socket of connection of the electromagnetic valve located under an inlet collector over a starter (it is specified by an arrow).
5. Disconnect a valve hose from an inlet collector and remove the valve together with hoses.
6. Installation is carried out upside-down removals.

On the homepage