Opel Astra A

1991-1998 of release

Repair and operation of the car



Opel Astra A
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Ventilation and heating
- 5. Power supply system
   + 5.1. Carburetor engines
   - 5.2. Models with fuel injection
      5.2.1. Technical characteristics
      5.2.2. Precautionary measures
      5.2.3. Elements of system of injection of fuel
      5.2.4. Unleaded gasoline
      5.2.5. Electronic control unit
      5.2.6. Casing of the air filter
      5.2.7. Air filter
      5.2.8. Resonator, air filter
      5.2.9. Fuel injection block (Multec of TsVT)
      5.2.10. Case of a butterfly valve (Multec of MW)
      5.2.11. Case of a butterfly valve (Multec-S)
      5.2.12. Case of a butterfly valve (Motronic M 1.5)
      5.2.13. Case of a butterfly valve (Motronic M 2.5 and M 2.8)
      5.2.14. Case of a butterfly valve (Simtec)
      5.2.15. Fuel injector of Multec of TsVT
      5.2.16. Fuel injectors of Multec of MW
      5.2.17. Fuel injectors (Motronic M 1.5)
      5.2.18. Fuel injectors (Motronic M 2.5 and M 2.8)
      5.2.19. Fuel injectors (Simtec)
      5.2.20. Fuel pressure regulator
      5.2.21. Sensor of provision of a butterfly valve
      5.2.22. Potentiometer of a butterfly valve
      5.2.23. Solenoid of system of idling
      5.2.24. Electromagnetic valve of system of idling
      5.2.25. The solenoid regulating air supply in system of idling
      5.2.26. Pressure sensor in an inlet collector
      5.2.27. Sensor of speed of rotation and provision of a bent shaft
      5.2.28. Sensor of temperature of cooling liquid
      5.2.29. Oxygen sensor
      5.2.30. The sensor of temperature of the arriving air
      5.2.31. Air stream sensor
      5.2.32. Sensor of detonation combustion of fuel
      5.2.33. Sensor of position of the camshaft
      5.2.34. Blowing-off valve of the coal filter
      5.2.35. Fuel pump
      5.2.36. Fuel filter
      5.2.37. Accelerator rope
+ 6. System of decrease in toxicity
+ 7. Coupling
+ 8. Transmissions
+ 9. Half shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
+ 13. Electric equipment
+ 14. Electrical circuitries


0a910c3c




5.2.13. Case of a butterfly valve (Motronic M 2.5 and M 2.8)

Removal and installation

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Uncover the air filter.
3. Disconnect the socket of connection of the sensor of provision of a butterfly valve.
4. Turn off a fixing nut and remove an arm of a fuel hose on the left side of the case of a butterfly valve.
5. Disconnect an accelerator rope from the lever of a butterfly valve.
6. Disconnect a ventilating hose on the forward party of the case of a butterfly valve.
7. Check that all hoses, wires and ropes were disconnected.
8. Turn off four fixing nuts (two of them are shown by shooters) and remove the case of a butterfly valve from an inlet collector. Remove laying.
9. The sensor of provision of a butterfly valve can be removed from the case of a butterfly valve.
10. Do not try to adjust the connecting mechanism of a butterfly valve. If it is faulty, address experts.
11. Installation is carried out upside-down removals. Before installation check adjustment of the sensor of provision of a butterfly valve. Establish new laying.

On the homepage