Opel Astra A

1991-1998 of release

Repair and operation of the car



Opel Astra A
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. SOHC engines
   + 3.2. DOHC engines
   - 3.3. Diesel engines
      3.3.1. Gear belt
      3.3.2. The 1,7 l diesel engine with a turbo-supercharging
      3.3.3. Tension of a gear belt
      3.3.4. The diesel TC4EE1 engine of 1,7 l with a turbo-supercharging
      3.3.5. Head of the block of cylinders
      3.3.6. The diesel TC4EE1 engine with a turbo-supercharging
      3.3.7. Check of a head of the block of cylinders and the block of cylinders on straightforwardness
      3.3.8. Camshaft
      3.3.9. Gas distribution phases
      3.3.10. Camshaft case cover oil separator
      3.3.11. Check and adjustment of gaps in the drive of valves
      3.3.12. Removal and installation of valves
      3.3.13. Replacement of oil scraper caps
      3.3.14. Grinding of valves
      3.3.15. Grinding in of valves
      3.3.16. Check of a gap in the directing plugs of valves
      3.3.17. Check of the directing plugs of valves
      3.3.18. Check of a compression
      3.3.19. Wedge-shaped belt
      3.3.20. Oil case
      3.3.21. Oil pump
      3.3.22. Safety valve
      3.3.23. Thermostat
      3.3.24. Check of kalilny candles
      3.3.25. Check of system of preliminary heating
      3.3.26. Removal of air from fuel system
      3.3.27. Check and adjustment of turns of idling
      3.3.28. Removal and installation of nozzles
      3.3.29. Check of an advancing of injection of fuel
      3.3.30. Heating of the fuel filter
      3.3.31. Replacement of the filtering element of the air filter
      3.3.32. Discharge of water from the fuel filter
      + 3.3.33. Useful tips
   + 3.4. Engine electric equipment
+ 4. Ventilation and heating
+ 5. Power supply system
+ 6. System of decrease in toxicity
+ 7. Coupling
+ 8. Transmissions
+ 9. Half shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
+ 13. Electric equipment
+ 14. Electrical circuitries


0a910c3c




3.3.24. Check of kalilny candles

GENERAL INFORMATION

Check conditions: the cold engine, completely charged accumulator (tension not less than 11,5 In).

PERFORMANCE ORDER
1. Disconnect wires from kalilny candles. Connect one conclusion of the voltmeter to a positive conclusion of the accumulator, and serially to put other conclusion to each candle.
2. If the light-emitting diode lights up, so the candle is serviceable and if is not present – that is faulty and are subject to replacement. The moment of an inhaling of candles – 20 Nanometers.

Prevention

Not to exceed the specified moment, otherwise the gap between filament and a carving will disappear, and the candle will prematurely fail.


3. Connect wires to kalilny candles.

Check of the relay of kalilny candles

PERFORMANCE ORDER
1. Remove the relay of kalilny candles (N8 relay). It is in the relay block in a motor compartment.
2. To put a sampler to the plug 30. To include ignition. The light-emitting diode of the device has to light up, otherwise check accumulator tension.
3. To put a sampler to the plug 86. To include ignition. The light-emitting diode of the device has to light up, otherwise check tension on the ignition lock.
4. If the light-emitting diode of a sampler blinks, to check for break of a wire of kalilny candles, if necessary to replace them or the relay.
On the homepage